BA datasheet, BA circuit, BA data sheet: ROHM – Fm Stereo Transmitter,alldatasheet, datasheet, Datasheet search site for Electronic. Page 4. Page 5. This datasheet has been downloaded from: Datasheets for electronic components. Part, BA Category, Communication => Freq/Signal Converters/Generators. Description, FM Stereo Transmitter. Company, ROHM Electronics. Datasheet.

Author: Malat Teshakar
Country: Antigua & Barbuda
Language: English (Spanish)
Genre: Life
Published (Last): 2 August 2007
Pages: 70
PDF File Size: 3.5 Mb
ePub File Size: 16.3 Mb
ISBN: 727-2-34296-684-6
Downloads: 68628
Price: Free* [*Free Regsitration Required]
Uploader: Zolorr

This is done for matching the frequency response of the FM transmitter with the FM receiver. To make matters worse, the music would modulate the high frequency tone. Network C9,C10, R4,R5 improves the channel separation. It also had an additional very slight high frequency tone. No use post-morteming the BA as it’s gone, but hopefully the kit manufacturers will do their NJM kits properly.

I found that the stuff that one channel was putting into the other channel was low level but really distorted bad. Wanna have your own page here, write about your own experiences, own review, refute existing review, add comments to existing review, publish your circuits? Thank you in advance. Hello, how can I variate the output frequency? I lost the “Stereo” and the “Tune” lamps on my receiver which began outputting odd sounds and beats.

Datasheer was very slight but it was always there.

Can it be possible to make a radio mp3 broadcast a long distance without buying an external boaster? The PCB is very good quality and so are the components.

Inductor L1 and capacitor C5 is used to set the oscillator frequency.

The FM Stereo rules say that the Pilot should be a sine wave, not square as square wave would have harmonics. These harmonics would fall into the higher part of the MPX signal, deceiving the receiver into feeling datasehet there was extraneous content in the original Audio channels. Tuning was easy, The signal moved around by only 25 KHz initially till Thermal equilibrium was reached.

  AR 380-28 PDF

I was expecting a low level of signal to ooze through to the other channel, but not so distorted!! Please give me the address.

High quality Stereo FM transmitter using BA

C I ran a 20HzKHz sine wave sweep signal through. Definitely NOT the chip to base your 5 W transmitter to broadcast around the town. I had to put my equaliser’s bass buttons up a bit. The Stereo light on my receiver came on immediately. Maybe that’s the reason for the deficiencies noted above? The BA is gone, long live the BA!! There were mailing lists and ftp sites arguing about the pros and cons of BA kits.

Can you send me.

Datasheets search archive of electronic components datasheets

C13 and C14 are just coupling capacitors, nothing to do with pre-emphasis. I have a problem with this coil. What is left in and right in. Your email address will not be published. Leave a Reply Cancel reply Your email address will not be published. Add them up passively, just making sure they are datasheey phase More complete method: Not noticeable when you play rock, but when I played the Bass drum track, after each drum beat, the high frequency note would ring and then stabilise a second later.

BA Datasheet pdf – Fm Stereo Transmitter – ROHM

I tried different antenna and found that could shift the operating frequency by KHz. That’s not as easy as it seems, you can write a book on Audio filters. The kit took me about an hour to make. The BA has to be fed by a regulated voltage because it accepts only 3.


The Documentation describes how to make the kit very well, but does not mention any technical facts at all. A The CK was much noisier to begin with. I really wonder if this slight high frequency note was caused by lack of a double sided board and large ground areas? I need a BA IC.

As expected the kit went berserk at the high end. However, what I liked best about the BA was the amount of excitement it created among the hobbyists.

There is enough place to work around easily. The kit pre-emphasizes the Audio inputs passively. Cana Kit claim mtr range in the open. Radio Transmitters Previous post Next post You may also like: Stereo Generators do need Limiters because the slightest clipping gives rise to distortion that is not harmonic.

Suppose you have a 10 KHz Audio signal and it is clipped a bit, it will generate harmonics. However the PCB is single sided and does not have large ground areas. A high quality stereo FM transmitter circuit is shown here.

The harmonics generated are harmonics, ie still slightly pleasing to the ear. But horrors, I put in only one channel of Audio and ground the other channel’s input. For that I would like two copies of 38 kHz quartz please.